Commercial LVT Flooring for Specification & Fit-Out Projects

Impervia vs Traditional LVT: Installation, Performance & Costs

Comparing rigid-core composite flooring with glue-down LVT for commercial projects

When specifying commercial flooring, the material price per square metre is only part of the picture. Subfloor preparation, adhesive, fitting labour, programme time and long-term maintenance all contribute to the total installed cost, and to how smoothly a project is delivered.

This guide compares Impervia, a rigid-core composite commercial LVT alternative, with traditional glue-down LVT, so you can judge which is the better fit for your project.

See the comparison table Discuss your specification

What Is Traditional Glue-Down LVT?

Traditional commercial LVT (luxury vinyl tile), often called dryback LVT, is a flexible vinyl floor covering made from a printed design layer and a clear wear layer over a vinyl base. It is supplied as thin tiles or planks that are bonded to the subfloor with adhesive.

Because the tiles are thin and flexible, the subfloor is normally prepared to a smooth, level, dry finish, often with a smoothing compound, so that imperfections do not show through. Adhesive is then applied and the tiles laid within its open time, rolled and left to cure before the floor is put into full use.

Glue-down LVT is widely specified and well understood by commercial flooring contractors. It offers a very broad range of designs, borders and inlays, a low floor build-up, and a fully bonded floor that suits many demanding commercial areas.

What Is Impervia?

Impervia is rigid-core composite flooring with a stone-based composite core. The published Environmental Product Declaration (EPD) describes Impervia as Stone Polymer Composite flooring.

Each 6.5mm board is made up of a UV coating, a 0.5mm commercial-grade wear layer, a décor film, a rigid stone-based composite core and an integrated 1.5mm IXPE acoustic backing. The boards lock together with the Välinge 5G-i click-fit system and are laid as a floating floor, with no adhesive and no separate underlay.

Impervia still needs a flat, sound and suitably prepared subfloor, and in refurbishment projects it may be installed over some suitable existing floors once they have been assessed. It is available in wood-effect planks, herringbone parquet and stone-effect tiles.

Impervia vs Traditional LVT: Comparison Table

The table below gives a general comparison. Glue-down LVT products vary widely, so always compare specific products, use classes and installation systems for your project.

Feature Impervia Traditional Glue-Down LVT

Construction

Rigid-core composite

Flexible vinyl

Installation

Click-fit

Adhesive

Acoustic backing

Integrated

Product-dependent

Subfloor requirements

Suitable prepared subfloor

Suitable prepared subfloor

Refurbishment

May be installed over some suitable existing floors

Preparation depends on conditions and installation system

Installation efficiency

Designed for efficient fitting

Requires adhesive installation stages

Installed cost

Potential savings in suitable projects

Varies by specification and labour

Maintenance

Practical routine maintenance

Practical routine maintenance

Designs

Wood and stone-effect finishes

Wide range of decorative finishes

Total Installed Cost

Comparing flooring on supply price alone can be misleading. Impervia’s supply price may be higher than some conventional LVT products, but on suitable projects the overall installed cost can be lower. When comparing quotations, look at every stage:

  • Material supply – the price per square metre of the flooring itself, plus any separate underlay.
  • Adhesive – glue-down LVT needs adhesive and the labour to apply it. Impervia’s click-fit system needs none.
  • Subfloor preparation – both systems need a suitable base. Thin flexible LVT typically needs a smooth, levelled surface; a rigid board can be more tolerant of minor surface texture, but the subfloor must still be flat and sound.
  • Labour and fitting time – removing the adhesive stage and the separate underlay can reduce fitting time and labour on suitable projects.
  • Programme time – there is no adhesive curing period, which can help phased works and occupied buildings.
  • Maintenance and repair – both need routine cleaning. Individual Impervia boards can be lifted and replaced using the click-fit system.

Actual costs and savings depend on project size, subfloor condition, labour rates and specification. For a fuller breakdown, see cost-effective commercial flooring, or ask our team for a project-specific comparison.

Durability and Performance

Both glue-down LVT and Impervia are made for commercial use, and performance depends on the specific product, use class and installation. The main differences are in construction rather than one system being better in every situation.

Wear and everyday use

Impervia has a 0.5mm commercial-grade wear layer with a ceramic lacquer finish, and its product data sheets list EN 649 class 34 (very heavy commercial). Commercial glue-down LVT is also available in a range of use classes and wear layer thicknesses, so compare like for like. Read more about Impervia’s durability.

Subfloor tolerance

A rigid core is less likely to show minor subfloor imperfections than a thin, flexible tile, although both systems need a flat, sound subfloor prepared in line with the manufacturer’s guidance.

Acoustics

Impervia’s backing is integrated into every board. In laboratory testing to BS EN ISO 10140-3 (SRL Technical Services, 2019), a loose-laid 6.5mm Impervia sample on a 160mm concrete reference floor achieved a weighted impact sound reduction (ΔLw) of 21 dB. Performance in a finished building depends on the floor construction and site conditions. Acoustic performance of glue-down LVT depends on the product and any acoustic underlay or backing specified.

Slip resistance

In independent pendulum testing (BS 7976-2, slider 96, SATRA 2019), the tested sample recorded wet PTV values of 38–40 and dry values of 64–69, classed as low slip potential under UK Slip Resistance Group guidelines. Slip resistance of glue-down LVT varies by product and finish. In every case, slip risk also depends on contamination, cleaning and footwear.

Moisture and spills

The stone-based composite core is not susceptible to moisture in normal use and the surface is designed to resist everyday spills. Subfloor moisture still needs to be assessed in line with the installation guidance. Glue-down LVT also relies on the adhesive and subfloor being kept within the manufacturer’s moisture limits.

Installation

Impervia’s click-fit system removes the adhesive stage; see easy-to-install flooring for how installation works in practice.

Which Flooring Is Right for Your Project?

The right choice depends on the building, the programme, the subfloor and how the space will be used. Both systems have their place: use the comparison above as a starting point and ask our technical team to review your project.

Where Impervia may offer advantages

  • Refurbishment projects where existing floors may be retained once assessed
  • Tight programmes and occupied buildings, where there is no adhesive curing time
  • Apartments, student accommodation, hotels and care homes where an integrated acoustic backing is useful
  • Spaces where boards may need to be lifted, replaced or reused
  • Wood-effect schemes looking for an alternative to engineered wood flooring

Where glue-down LVT may still be preferable

  • Areas with heavy rolling loads or frequent wheeled traffic, where a fully bonded floor is specified
  • Projects with very limited floor build-up or tight threshold details
  • Schemes needing bespoke borders, inlays or a specific decorative range
  • Wet rooms and areas needing a sealed, welded or specialist hygienic floor system
  • Projects where a particular LVT product is already specified

Frequently Asked Questions

Is Impervia a type of LVT?

Impervia is positioned as a commercial LVT alternative. It is rigid-core composite flooring, and its EPD describes it as Stone Polymer Composite flooring, rather than a conventional flexible luxury vinyl tile.

Does Impervia need adhesive?

No. Impervia boards lock together with the Välinge 5G-i click-fit system and are laid as a floating floor over a suitable prepared subfloor.

Can Impervia be installed over an existing floor?

In some refurbishment projects, yes. Existing floors must be assessed for flatness, soundness and moisture first, and prepared where necessary. Not every existing floor will be suitable.

Is Impervia cheaper than glue-down LVT?

Not always on supply price. The potential saving is in the total installed cost: no adhesive, no separate underlay and potentially less fitting time. Whether it is cheaper overall depends on the project.

How does the acoustic performance compare?

Impervia’s integrated IXPE backing achieved an impact sound reduction (ΔLw) of 21 dB in laboratory testing on a concrete reference floor. Glue-down LVT acoustic performance depends on the product and any acoustic layer specified.

Is Impervia suitable for wet areas?

Impervia’s stone-based core is not susceptible to moisture in normal use and its surface is designed to resist everyday spills, making it suitable for areas such as kitchens and cafés. It is not a sealed wet-room floor system, and it is not suitable for every wet environment.

Can Impervia be used in care homes and hospitality venues?

It is used in hospitality and residential settings, and the sample tested showed low slip potential in wet and dry pendulum testing. Because slip risk depends on the environment, cleaning and footwear, a project-specific slip-risk assessment should always be carried out.

Can individual boards be replaced?

Yes. The click-fit system allows individual boards to be lifted and replaced if an area is damaged, following the fitting guidance.

Discuss Your Flooring Specification

Comparing Impervia with glue-down LVT for a specific project? Our technical team can review your subfloor, programme and performance requirements, provide product data sheets and test reports, and arrange samples or mock-up boards.

Discuss your specification Visit the technical library

Talk to our flooring experts
Call us
01666 504 015
Address
Unit 1 Helena Court
Gloucestershire GL8 8JN
This field is for validation purposes and should be left unchanged.
INFO